Hey all, just finished my first Fina conversion and have a small problem. I started with a 4 gm kit (2 cartridges) and the finakit I got included too much oil. Basically, I ended up with 60ml instead of 40ml. I looked at the conversion table and believe that I have approx. 57mg/ml. Can anyone confirm this or point me in the right direction. Thanks a lot
Posted by: ROID
Originally Posted by ravenboy68
Hey all, just finished my first Fina conversion and have a small problem. I started with a 4 gm kit (2 cartridges) and the finakit I got included too much oil. Basically, I ended up with 60ml instead of 40ml. I looked at the conversion table and believe that I have approx. 57mg/ml. Can anyone confirm this or point me in the right direction. Thanks a lot
Unfortunately in theory you have 57 mg/ml. There is no way to tell exactly what mg/ml you have when you use those kits. Some kits estimate a 25% loss , some 0% loss, ie 100mg/ml.
You probably have way less than the 57mg/ml.
subtract at least 25% from your estimated concentration.
Posted by: brundel
You may have had 57mg/ml if like the kit likely states the expected mg/ml produced was 100mg. Since the kits are garbage and leave you with something like 50mg/ml when done right you now have something like 20mg/ml.
Posted by: brundel
You dont need a kit.
1 crush the pellets in a pyrex measuring cup.
2. add 150ml methanol. Heet in the yllow and blue bottle will work.
Allow 30 min to dissolve.
3. pour through a coffee filter. Make sure to capture the fluid in another pyrex measuring cup or 700+ml bomex beaker. This fluid is where your tren is.
4. pour 500ml ice cold water into the fluid. You will see the tren appear.
5. pour this through a Brown cone shaped coffee filter. Dont buy cheap ones.
There is now tren powder in the filter.
6. rinse at least 3-4 times with distilled water by pouring through the filter.
7. Allow 24 hours at least to dry. I like to put it in a bowl with a lamp over it. DO NOT PUT IN OVEN>
Once dry it is ready to be weighed and prepared for injection.
Posted by: brundel
Once you have the powder you can weigh it and prep it at whatever mg/ml you want.
100% certain what it will produce.
Not guesstimating based upon the recommendations of some shady kit dealer.
Posted by: SUPERFLY1234
Originally Posted by brundel
You dont need a kit.
4. pour 500ml ice cold water into the fluid. You will see the tren appear.
did you really mean cold distilled water? i would not like any more chemicals in my body. i always add the water in slow. that way you get more from your conversion.
Posted by: ROID
Originally Posted by SUPERFLY1234
did you really mean cold distilled water? i would not like any more chemicals in my body. i always add the water in slow. that way you get more from your conversion.
I put mine in the freezer and let it drip.
You think cold distilled water is a bad idea ?
Posted by: ROID
Originally Posted by brundel
Once you have the powder you can weigh it and prep it at whatever mg/ml you want.
100% certain what it will produce.
Not guesstimating based upon the recommendations of some shady kit dealer.
What % loss do you usually end up with ?
Posted by: SUPERFLY1234
Originally Posted by ROID
I put mine in the freezer and let it drip.
You think cold distilled water is a bad idea ?
cold, cool, or room temp. distilled water is what i always use. after my conversion i get around 1.9 grams of powder. not bad for a guy who uses coffee filters and old pickle jars.
Posted by: ROID
Originally Posted by SUPERFLY1234
cold, cool, or room temp. distilled water is what i always use. after my conversion i get around 1.9 grams of powder. not bad for a guy who uses coffee filters and old pickle jars.
wow, you get 90%.
I get max 75% from one cart.
Do you think the MA is completely evaporated once the powder dries ?
Originally Posted by ravenboy68
