Prince

F-TYPE

Step 1
Smash pellets into a fine powder

Step 2
Add powder to dissolving solution (2mls per cart) Shake until fully dissolved up to 15 minutes.

Step 3
Add oil (set aside 5mls), place sealed vial in hot water for 10 minutes to fully release hormones, shake vigorously and dump into coffee filter fixed to a glass or ceramic container. Allow to drip through (this removes binders and fillers) and swirl around gently to help through filter. Once all has passed through just throw away coffee filter ( This does take a long time so you may want to ring the filter to speed things up).

Step 4
Now pull mixture into syringe, attach syringe filter and pin and push through into sterile sealed vial.

Step 5
Now detach filter and pin, pull remaining oil into syringe, attach filter and pin again and push through into mixture until 20, 40, 60, 80 or 100mls is reached in vial. This will purge the filter of any remaining product and complete our conversion.

As long as there are no particles in the final yield you have very clean and sterile product.



S-TYPE


Separation Instructions

Materials needed for every 5 cartridges:
1 yellow bottle of Heet (methanol 355ml)
Coffee filters
Large glasses or jars
Distilled water
3cc of estrogen solubilizer


Filtration

When filtration is mentioned, it refers to placing a coffee filter over a glass or jars and pouring whatever is to be filtered through to coffee filter, into the glass or jar. A rubber band can be used to help secure the filter.

Step 1 - Dissolve Pellets in Methanol
Dissolve 5 carts in one bottle of Heet. When pellets are dissolved, extraction is complete. Agitation and stirring will help speed up the process.


Step 2 - Filtration
Filter out the binders, squeezing the last drops of methanol solution out of the filter. You now have a methanol solution containing approximately 1g estradiol benzoate and 10g test prop.


Step 3 - Estrogen Solubilization
Add contents of the estrogen solubilizer vial to the methanol solution. Let this stand for 1 hour, no more, no less. Some precipitation may occur, that is ok.

Step 4 - Test Prop Recovery
Add 500ml water to the methanol solution. It will look like milk when the water is added, this is the test prop coming out of solution. Let this sit for 5-10 minutes, until it looks filterable (clumpy, not like milk).

Step 5 - Filtration
Filter out the test prop as described. Let the filter completely drain, then rinse with water. Repeat this rinsing 2 more times. Now you have pure testosterone propionate, allow it to dry and it is ready for processing.


Powder Conversion Instructions Once Recovered

Step 1
Place powder in vial.

Step 2
Add all BA to the vial.

Step 3
Add oil to the vial, save 2 ml of oil in the small syringe for later. Gently shake vial.

Step 4
Heat mixture by placing sealed vial in hot water for 10 minutes to fully release hormones.

Step 5 - Filtration
Draw mixture into large syringe, attach syringe filter and 18G needle (place another small needle in vial to vent) then press into sealed sterile vial repeating until conversion complete.

Step 6
Take other syringe with 2ml oil, run through Whatman into solution.


Makes 100ml @ 100mg/ml with 10gm powder recovered and 5C kit

OR

Makes 200ml @ 100mg/ml with 20gm powder recovered and 10C kit


Universal Kits for all of your research chemical needs.

Support the Board Sponsors:

• SBMuscle.com - Discount Supplement Superstore
• AlltheWhey.com - Bulk Protein Powders
• CEM Products - Research Chemicals & Supplements
• MusclePharm - Complete Nutritional Arsenal
• BigBackGrips - If you lift weights you've got to try these grips!

CHECK OUT THIS NEW 6-PACK-ABS PROGRAM!