IronMag Research Chems


Sterilization

Results 1 to 14 of 14

Thread: Sterilization

  1. #1
    Registered User


    Join Date
    Nov 2010
    Gender
    Male
    Location
    California
    Posts
    48
    Rep Points
    247779

    Sterilization

    I was reading about sterilizing my roids by placing in an oven with a syringe inside the vial to equalize the pressure and allowing it to bake at a certain temperature for a certain time. Ive read about how UGL's do not have the same strict safety standards as the major pharmaceutical company and that this can be a convenient way to safely sterilize your own gear. Has anyone heard anything about this? I dont want to destroy my gear.

  2. #2
    Registered User
    twotuff's Avatar


    Join Date
    Mar 2011
    Gender
    Male
    Location
    CALI
    Posts
    1,061
    Rep Points
    45771981

    yes and the big question do u trust your source? if you even think it is dirty why would you use it?!?

  3. #3

  4. #4
    Twisted Steel
    cutright's Avatar


    Join Date
    Nov 2010
    Gender
    Male
    Location
    midwest
    Posts
    703
    Rep Points
    45144422

    It won't hurt your gear...if it makes u sleep better vent it with a 25g and bake at 215 for 20 minutes

  5. #5
    Senior Member
    ELITE MEMBER
    Mr.BIG's Avatar


    Join Date
    Jan 2011
    Gender
    Male
    Location
    U.S.A.
    Posts
    1,028
    Rep Points
    48094048

    Quote Originally Posted by World-Pharma.org View Post

    Nice video!

  6. #6
    Moderator
    MODERATOR
    TGB1987's Avatar


    Join Date
    Feb 2011
    Gender
    Male
    Location
    Pennsylvania
    Posts
    2,482
    Rep Points
    490784210

    Heat sterilization is the simpliest way to sterilize injectable AAS. The typical way to do so is to place the AAS vial in the oven for 30 min at 250 degree F. Leave a needle sticking through the rubber stopper to equilize pressure inside the vial, or it may break. This should kill most bacteria, and can be regarded as a viable harm reduction strategy.
    Other choose to use the top of the stove to heat sterilize. You submerge the AAS vials in a pot of boiling water 212 degrees F. Keep the vial kept in the water for approximately 20-30 minutes. Though this will kill many forms of bacteria and microorganisms it is not considered the best method of doing so. A higher temp should be used. Also if the vial sits on the bottom of the pot it will be in direct contact with the heat source which will make it hard to control the temp in the vial.
    Note that tren breaks down at fairly lover temps. It begins to degrade even at 212 degrees F. Tren should be heat sterilized under different conditions . Typically baking the vial in an oven for two hours at 175 degrees F. Again an unattached needle should be placed in the rubber stopper.

    Another way to sterilize is to use a syringe filtration. .22 micron filters allow for the removal of all most all forms of bacteria. If you want me to go into detail of how to do this let me know and I will post it up.
    Keep in mind these methods are not without flaw. For example you have to be careful not to contaminate your own gear while doing filtering your AAS. Also many forms of bacteria are small and hardy enough to survive these techniques. The safety methods I stated are highly effective, but not necessarily complete. To be safe it is best to use legitamite pharmaceutical products.



  7. #7
    Senior Member
    ELITE MEMBER


    Join Date
    Nov 2009
    Gender
    Male
    Location
    usa
    Posts
    745
    Rep Points
    151075733

    Dumb question guys. Would venting the vial and then putting it under vacuum (without heat) kill the bacteria?

  8. #8
    Moderator
    MODERATOR
    TGB1987's Avatar


    Join Date
    Feb 2011
    Gender
    Male
    Location
    Pennsylvania
    Posts
    2,482
    Rep Points
    490784210

    What do you mean by vacuum?



  9. #9
    Senior Member
    BOARD REP
    World-Pharma.org's Avatar


    Join Date
    Mar 2010
    Gender
    Male
    Location
    europe
    Posts
    9,591
    Rep Points
    595401826

    Video tell you how real GMP steroids made so FDA can approved it.

  10. #10
    Registered User


    Join Date
    Nov 2010
    Gender
    Male
    Location
    California
    Posts
    48
    Rep Points
    247779

    I trust my source because i've used gear from him before and he's on his own supply. But just for myself I know ug labs dont have the same FDA safety standards as the big pharmaceutical companies and that's to be expected big time labs have gargantuan budgets to meet the strict safety guidelines imposed on them by the government. Thank you for the tips guys ill use them, i didnt know that about the tren TGB1987 thanks for the heads up bro before i baked away a chunk a change

  11. #11
    Moderator
    MODERATOR
    TGB1987's Avatar


    Join Date
    Feb 2011
    Gender
    Male
    Location
    Pennsylvania
    Posts
    2,482
    Rep Points
    490784210

    No problem, glad you posted this before trying it.



  12. #12
    Senior Member
    ELITE MEMBER


    Join Date
    Nov 2009
    Gender
    Male
    Location
    usa
    Posts
    745
    Rep Points
    151075733

    Quote Originally Posted by TGB1987 View Post
    What do you mean by vacuum?

    Put it in a vacuum chamber.

  13. #13
    Moderator
    MODERATOR
    TGB1987's Avatar


    Join Date
    Feb 2011
    Gender
    Male
    Location
    Pennsylvania
    Posts
    2,482
    Rep Points
    490784210

    Never heard of anyone doing that before.



  14. #14
    Senior Member
    ELITE MEMBER


    Join Date
    Nov 2009
    Gender
    Male
    Location
    usa
    Posts
    745
    Rep Points
    151075733

    Quote Originally Posted by TGB1987 View Post
    Never heard of anyone doing that before.

    Me either. That's why I was wondering if it was a stupid idea or if the lack of any air and pressure kills bacteria?

Similar Threads

  1. Sterilization techniques for AAS
    By TGB1987 in forum Anabolic Zone
    Replies: 16
    Last Post: 07-25-2011, 01:07 PM
  2. Replies: 62
    Last Post: 07-24-2010, 03:30 PM
  3. Sterilization...
    By RexLozano in forum Anabolic Zone
    Replies: 5
    Last Post: 08-28-2006, 01:25 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
-->