Tren pro's... Problem with my injection?

[heartofalion]

I am running 100 Tren Ace ED, 50 Pro ED, and 250 Deca EW. I preloaded some syringes and had them in my car, in the heat. I've injected 3 of those out of my car, and got immediate, big time Tren cough, nasty itching, and just a terrible feeling physically that all subsided within minutes. It's pretty clear to me that this was because I left these in the heat, but i'm curious if anyone has a good explanation of why this happens, and if any active hormone was compromised.

 

[Hate4TheWeak]

Was the tren made from fina pellets?

 

[Hate4TheWeak]

If so...when the binder gets heated like that it can fuck with you.

 

[heartofalion]

I really doubt it was pellets, because this is from a full line underground lab. Top notch stuff. It's like Tren cough times 50. Normally Tren cough is nothing for me. This Tren feels clean, clean, but after sitting there in the car a few days it turned into like mutant Tren lol. Could be the Prop too, but since the feeling is classic Tren sides, just multiplied, I gotta assume it's the Tren. I normally heat each injection in hot water, so I didn't see why this would turn ugly like that.

 

[Hate4TheWeak]

Yeah, That doesn't make much sence... Hmm.. If the tren was made with high levels of solvents BB and BA and it sat in preloaded pins if could have eaten away at the plastic, especially the rubber plunger...

 

[heartofalion]

Hmmmm... That's gotta be it - it's ethyl oleate, not gso. I know I've read about EO eating away at syringe innards. Good call buddy!

 

[overburdened]

I am running 100 Tren Ace ED, 50 Pro ED, and 250 Deca EW. I preloaded some syringes and had them in my car, in the heat. I've injected 3 of those out of my car, and got immediate, big time Tren cough, nasty itching, and just a terrible feeling physically that all subsided within minutes. It's pretty clear to me that this was because I left these in the heat, but i'm curious if anyone has a good explanation of why this happens, and if any active hormone was compromised.

you are either injecting into a pocket of fluid(that is exposed to blood flow... a good amt of blood flow) or nicking or going through a vessel and out other side.... if you go through and out, you wont get a flash usually when you aspirate the syringe, same with nicking a vessel... but the tren will follow back the course of the needle and hit your bloodstream and cause what SFW likes to refer to as a 'Trenbolism' which is a damn good description ! the tren is causing a small embolism when it enter bloodstream at a reasonable rate of speed...

 

[overburdened]

Yeah, That doesn't make much sence... Hmm.. If the tren was made with high levels of solvents BB and BA and it sat in preloaded pins if could have eaten away at the plastic, especially the rubber plunger...

^^^this too, is highly likely!!! way to go on that thinking H4TW... I taught you well, grasshopper!

 

[Hate4TheWeak]

^^^this too, is highly likely!!! way to go on that thinking H4TW... I taught you well, grasshopper!

Thank you sir...

 

[Hate4TheWeak]

lolzerz

 

[Hate4TheWeak]

Hmmmm... That's gotta be it - it's ethyl oleate, not gso. I know I've read about EO eating away at syringe innards. Good call buddy!

Yeah don't preload those shits next time brother!!

 

[GreenGiant]

Whenever I pin tren....I put a red bandana on, a pair of aviators, and belt of bullets around my shoulder for a full on Rambo effect....ohya and a wig complete with a fan to blow the hair around.

Question: Was this the 1st pin of the tren from this particular batch that your running?

 

[heartofalion]

Whenever I pin tren....I put a red bandana on, a pair of aviators, and belt of bullets around my shoulder for a full on Rambo effect....ohya and a wig complete with a fan to blow the hair around.

Question: Was this the 1st pin of the tren from this particular batch that your running?

No, it's somewhere in the middle of my 25ml jug. Every other injection has been the tits.