Mast/Tren/Prop Cycle

[cumminspower]

Just wanting to get opinions.

1-12 Tren Ace .5mL ED
1-12 Test Prop .5mL ED
1-12 Mast Prop .5mL ED
Cabaser .5mg 2x wk
HCG 250iu 2x wk
Clomid and Nolva for PCT

Using 29G slin pins, so Im not too concerned about scar tissue.

Age: 34
Weight: 205
Height: 6'3
BF: 13%

 

[sendit08]

Just wanting to get opinions.

1-12 Tren Ace .5mL ED
1-12 Test Prop .5mL ED
1-12 Mast Prop .5mL ED
Cabaser .5mg 2x wk
HCG 250iu 2x wk
Clomid and Nolva for PCT

Using 29G slin pins, so Im not too concerned about scar tissue.

Age: 34
Weight: 205
Height: 6'3
BF: 13%

no way to give opinions if we dont know the translation .5ml to how many mgs?

 

[theCaptn']

0.5 is going to be 50mg max.

All looks good to me.

May want to try ramping up tren a little during the last 4 weeks. Using slin pins you can make micro-adjustments real easy.

 

[Don't_fake]

Slin pins will work for hcg but I don't think you can shoot sub-q with the other compounds.

 

[Don't_fake]

0.5 is going to be 50mg max.

All looks good to me.

May want to try ramping up tren a little during the last 4 weeks. Using slin pins you can make micro-adjustments real easy.

You can use slin pins? See I didn't know that I was always told not to

 

[TrojanMan60563]

I don't know how people shoot IM with a 1/2" 29g slin pin. Even if you're super lean is 1/2" deep really good enough for an IM injection? Even if I was single digit BF I don't think I'd buy anything shorter than 1". I know smaller needle less scar tissue. I've bought some 25g pins just to revisit the oil through a small needle trip again. I also purchased some 23g to replace the current 22g needles I use which I don't really mind.

 

[cumminspower]

the Tren mast and prop are all 10g per mL

 

[cumminspower]

Stupid phone 100mg per mL

 

[sendit08]

Stupid phone 100mg per mL

just to add my 2 cents...
I like the fact that you didnt go the route of a blend to save a bit of $$
personally I just came off of a blend to three seperate compounds so that I can better adjust my levels.

 

[Tris10]

I don't know how people shoot IM with a 1/2" 29g slin pin. Even if you're super lean is 1/2" deep really good enough for an IM injection? Even if I was single digit BF I don't think I'd buy anything shorter than 1". I know smaller needle less scar tissue. I've bought some 25g pins just to revisit the oil through a small needle trip again. I also purchased some 23g to replace the current 22g needles I use which I don't really mind.

I use 1/2inch slin.. just dimple the skin so it goes deeper. You're right about the bf% part, kinda.. what I do is more for ppl 15%have and under imo.. could be wrong, I stay pretty lean tho so Idk about above 15%

 

[rage racing]

Just wanting to get opinions.

1-12 Tren Ace .5mL ED
1-12 Test Prop .5mL ED
1-12 Mast Prop .5mL ED
Cabaser .5mg 2x wk
HCG 250iu 2x wk
Clomid and Nolva for PCT

Using 29G slin pins, so Im not too concerned about scar tissue.

Age: 34
Weight: 205
Height: 6'3
BF: 13%

I would drop the test dose a little and bump up the mast. Slin pins are great if your lean but remember, the only hold a ml and you will be pinning 1.5ml ed.

 

[sendit08]

I would drop the test dose a little and bump up the mast. Slin pins are great if your lean but remember, the only hold a ml and you will be pinning 1.5ml ed.

I use a normal drawing pin. 3ml with a 20g 1.5" needle then heat the oil then chage the needle for a 29g 1" some areas 3/4" other areas.

 

[president]

Running something similar but low test/high tren (300mg/600mg) . I used 25g 5/8" on my arms without a problem (besides the first few times you have to break the muscle in with the oil).

 

[TrojanMan60563]

I use a normal drawing pin. 3ml with a 20g 1.5" needle then heat the oil then chage the needle for a 29g 1" some areas 3/4" other areas.

I remember using 25g needles with UGL stuff and it took forever to push 1cc even. I can't imagine how oil can go through a 29g pin...

 

[heavylifting1]

That cycle looks good to me!

 

[theCaptn']

I remember using 25g needles with UGL stuff and it took forever to push 1cc even. I can't imagine how oil can go through a 29g pin...

It goes just fine but need to backload. You don't need to be that lean to shoot im with skins, just stick to low bf areas like delts, tris n pecs.

 

[TrojanMan60563]

It goes just fine but need to backload. You don't need to be that lean to shoot im with skins, just stick to low bf areas like delts, tris n pecs.

I ordered some slin pins and some 25g to see if my take on small needles have changed. I did notice GPZ sells a 30g pin that attaches to a standard 3cc barrel. However maybe the thinner barrel of the slin pin makes it easier to push through.

Back to this guys thread topic masteron seems like a sweet drug from what I've read about it. I can imagine this cycle would make for a great cut and to get hard.

 

[Night_Wolf]

I would rather go:
Test 0.5ml eod
Tren 1.5ml eod
Mast 1ml eod
(or shoot ed, I just illustrated dosages)

No need for caber. Use hcg only if u know u need it.


Sent from my iPhone 4 using Tapatalk

 

[Night_Wolf]

I backload 2-3ml pins and put 26g 0.5" or 27g 0.75", zero pain, is awesome. Takes a little bit longer but worth it. Before I did 1ml slin pins but right now I'm injecting more than 1ml per shoot so... I shoot quads and delts.


Sent from my iPhone 4 using Tapatalk