Guys I'm using 23 G needles and have been through an amp already and had to throw it out cause the oil kept filling with air every time I would tr to pull the sust in the needle. It has a fucker of a time pulling on the oil and than even when I think that I'm pulling on the plunger reeeeeaaaly slow it pulls up and sucks up a shit load of air and tiny-micro bubble fill the oil. It's pissing me off? My friend has been through a map too trying to get this shit right without injecting us up with air bubbles. Can you guys give me some suggestions as to what the hell I'm doing wrong or what I have to do to get this shit in?
-
Hello, this board in now turned off and no new posting.
Please REGISTER at Anabolic Steroid Forums, and become a member of our NEW community!
-
Check Out IronMag Labs® KSM-66 Max - Recovery and Anabolic Growth Complex
can't seem to get my gear in the needle!!!
- Thread starter repoj
- Start date
- Joined
- Mar 24, 2003
- Messages
- 6,315
- Reaction score
- 16
- Points
- 0
- Location
- Just below our civil disguise
get an 18 g pin to draw with, it works wonders. I guarantee once you do that once you will never go back to trying to draw with a smaller g
If you think thats bad try a 25g, I use a 20g to pull. I can load an entire 3cc in a matter of seconds.
To pull out of an amp get a 1.5" 20g, and/or tilt the amp slowly which is how they were designed to be used.
To pull out of an amp get a 1.5" 20g, and/or tilt the amp slowly which is how they were designed to be used.
yea...I use 20's to fill and either a 23 or 25 depending on where I'm shooting...
If you are sucking up air, if not then ignore.
Create vacuum and WAIT, if you keep sucking up through a thing gauge needle and dont give the oil time to draw in, then yes you will pull in air. Its the path of least resistance - one of the basic laws of nature. Easier to pull in air from around the rubber seal than the oil if you dont give it time and are creating 20 pounds of vacuum.
Create vacuum and WAIT, if you keep sucking up through a thing gauge needle and dont give the oil time to draw in, then yes you will pull in air. Its the path of least resistance - one of the basic laws of nature. Easier to pull in air from around the rubber seal than the oil if you dont give it time and are creating 20 pounds of vacuum.
ok guys, I just heated up the amp and injected into my delt. I didn't get it all in buecause I forgot to aspirate the needle and when I started to push very gently on the plunger I remembered to aspirate and I started to see some blood. Very lilttle of the gear got in me and I totaly freaked out. Will this do anything to me now? Am I a dead man? I realy need some advise guys I'm kinda freaki'n out here.
repoj said:
why not just do glute shots ?
- Joined
- Feb 5, 2004
- Messages
- 300
- Reaction score
- 1
- Points
- 0
even if you suck up bubbles there is no need to throw away the gear man.... just let it sit for a while in the syringe, all the little bubbles will turn into 1 big one and you can just push it out.
thanks guys, you all gave me the support that I needed. I just tried it again and all the gitters and aprehension went out the window. It was slow, smooth, and it went in vertualy painless. I had some tiny tiny air bubble, but I aspirated and NO BLOOD!! Now I hope every other injection is this easy.
repoj said:
It takes only second for your blood to circulate your entire body...you wouldn't have had time to type this post if it was going to kill you. Luckily you caught it before injecting all the oil. I don't think many people die from injecting into a vein. Most people report the feeling of feeling like they can't breath. I injected P-GH sub-q and shot into a vein and it was a scary 5-10 seconds gasping for air but it went away and I felt freaked out for an hour or so after that.
