First time Fina conversion question!!

[ravenboy68]

Hey all, just finished my first Fina conversion and have a small problem. I started with a 4 gm kit (2 cartridges) and the finakit I got included too much oil. Basically, I ended up with 60ml instead of 40ml. I looked at the conversion table and believe that I have approx. 57mg/ml. Can anyone confirm this or point me in the right direction. Thanks a lot

 

[ROID]

Hey all, just finished my first Fina conversion and have a small problem. I started with a 4 gm kit (2 cartridges) and the finakit I got included too much oil. Basically, I ended up with 60ml instead of 40ml. I looked at the conversion table and believe that I have approx. 57mg/ml. Can anyone confirm this or point me in the right direction. Thanks a lot

Unfortunately in theory you have 57 mg/ml. There is no way to tell exactly what mg/ml you have when you use those kits. Some kits estimate a 25% loss , some 0% loss, ie 100mg/ml.

You probably have way less than the 57mg/ml.

subtract at least 25% from your estimated concentration.

 

[brundel]

You may have had 57mg/ml if like the kit likely states the expected mg/ml produced was 100mg. Since the kits are garbage and leave you with something like 50mg/ml when done right you now have something like 20mg/ml.

 

[brundel]

You dont need a kit.

1 crush the pellets in a pyrex measuring cup.
2. add 150ml methanol. Heet in the yllow and blue bottle will work.
Allow 30 min to dissolve.
3. pour through a coffee filter. Make sure to capture the fluid in another pyrex measuring cup or 700+ml bomex beaker. This fluid is where your tren is.
4. pour 500ml ice cold water into the fluid. You will see the tren appear.
5. pour this through a Brown cone shaped coffee filter. Dont buy cheap ones.

There is now tren powder in the filter.
6. rinse at least 3-4 times with distilled water by pouring through the filter.
7. Allow 24 hours at least to dry. I like to put it in a bowl with a lamp over it. DO NOT PUT IN OVEN>

Once dry it is ready to be weighed and prepared for injection.

 

[brundel]

Once you have the powder you can weigh it and prep it at whatever mg/ml you want.
100% certain what it will produce.
Not guesstimating based upon the recommendations of some shady kit dealer.

 

[SUPERFLY1234]

You dont need a kit.

4. pour 500ml ice cold water into the fluid. You will see the tren appear.

did you really mean cold distilled water? i would not like any more chemicals in my body. i always add the water in slow. that way you get more from your conversion.

 

[ROID]

did you really mean cold distilled water? i would not like any more chemicals in my body. i always add the water in slow. that way you get more from your conversion.

I put mine in the freezer and let it drip.

You think cold distilled water is a bad idea ?

 

[ROID]

Once you have the powder you can weigh it and prep it at whatever mg/ml you want.
100% certain what it will produce.
Not guesstimating based upon the recommendations of some shady kit dealer.

What % loss do you usually end up with ?

 

[SUPERFLY1234]

I put mine in the freezer and let it drip.

You think cold distilled water is a bad idea ?

cold, cool, or room temp. distilled water is what i always use. after my conversion i get around 1.9 grams of powder. not bad for a guy who uses coffee filters and old pickle jars.

 

[ROID]

cold, cool, or room temp. distilled water is what i always use. after my conversion i get around 1.9 grams of powder. not bad for a guy who uses coffee filters and old pickle jars.

wow, you get 90%.

I get max 75% from one cart.

Do you think the MA is completely evaporated once the powder dries ?