Hello i just got my order of hcg in......they came in ampules. Now i have never used them before? There is 1 ampule with this powder stuff in the bottum and another ampule of water it looks like. The question i have is each amp is 5000iu and i am only going to use 2500iu so do i draw the whole med into the needle use half? Then when i inject again change the tip, and then just inject other half ? Also i have googled on how to inject and stuff, it shows people using a filter to prevent glass from getting in do you need this or ? Thanks alot guys.
-
Hello, this board in now turned off and no new posting.
Please REGISTER at Anabolic Steroid Forums, and become a member of our NEW community!
-
Check Out IronMag Labs® KSM-66 Max - Recovery and Anabolic Growth Complex
How to use an ampule?
- Thread starter pimprn
- Start date
VictorZ06
Registered
This is how I use HCG. I mix the compound with the water, after doing so I pull it all out in a 3ml IM syringe. Once the solution is in the syringe, I take the needle off of the syringe and push the plunger to where there is no air inside (hold it upright so it doesn't pour out of the hole where the syringe goes).
Then I take my slin pin and put the slin pin needle in the opening of the IM syringe and draw what I need. So you can put 5000iu in the syringe and take out as much as you want, when you want it. Keep the IM syringe with the HCG stored in the fridge. You can also do this using a sterile vial and draw from there....but syringes are easier to come by than sterile bottles.
/V
Then I take my slin pin and put the slin pin needle in the opening of the IM syringe and draw what I need. So you can put 5000iu in the syringe and take out as much as you want, when you want it. Keep the IM syringe with the HCG stored in the fridge. You can also do this using a sterile vial and draw from there....but syringes are easier to come by than sterile bottles.
/V
thanks victor and im assuming you put a new needle tip back on when you are done drawing out of your 3ml syringe? and what about sterile purposes when i go to take more out? And do you have to use a insulin needle when injecting hcg or can i just use a regular 22g that i usually use to inject my sauce.?
fill an EMPTY UNSUSED SEALD STERIL vile witht he hcg and mix and put in fridge.
I never used a filter.
also only fill what u use PER TIME. or you may get an infection. common sence man.
dont let the stuff sit in a needle after you already used it. also remember AFTER MIXED KEEP IN FRIDGE AND ITS ONLY GOOD FOR 4-5 weeks!
Hammer-She-Rides
Registered
VictorZ06
Registered
Yes, I only use the IM pin once, than I switch it with a new one before it goes in the fridge and be sure to keep the air out of the syringe as well. If your hands are clean, sterility is not a problem as you are simply filling up an insulin syringe straight from an IM syringe. Both are sterile.
HCG can be taken via IM or Sub-Q. It's your choice. However, it's MUCH easier to use a slin pin for Sub-Q shots.
/V
ok victor sorry for the confusion here i think i have a grasp on whats going on. Ok this is my procedure i am going to confirm before i do it ok.
Steps:
Sanitize area.(and amps)
crack ampules open powder and water.
Draw solution out of amp change needle tip
fill water in powder.
Change needle tip
then draw the mix into my syringe.
then get another syringe draw out what i need from the one with the hcg.
Change needle tips
store in fridge and inject.
Steps:
Sanitize area.(and amps)
crack ampules open powder and water.
Draw solution out of amp change needle tip
fill water in powder.
Change needle tip
then draw the mix into my syringe.
then get another syringe draw out what i need from the one with the hcg.
Change needle tips
store in fridge and inject.
VictorZ06
Registered
Ok...follow these steps.
1. Break open both the solution and powder amps.
2. With an IM pin (long one) draw the water out and put it in the powder amp.
3. Draw the mixed solution into the IM syringe.
4. Take the pin off the IM syringe so you can see the small plastic hole (hold upright)
5. Take the slin pin and draw from the plastic hole on the IM syringe.
6. Push the IM plunger so that the solution touches the slin pin, and draw.
7. Store back in the fridge and replace IM pin.
The IM pin just keeps the syringe sealed when it's in the fridge. You won't pin it. It sounds confusing...maybe I'll make a video clip next time I crack open an amp.
You can use a sterile vial if you have one on hand, just keep in mind that every time a pin goes through the rubber stopper, it becomes dull/not as sharp. Another reason to use/draw from the IM syringe.
Hope I laid it out OK for ya.
/V
1. Break open both the solution and powder amps.
2. With an IM pin (long one) draw the water out and put it in the powder amp.
3. Draw the mixed solution into the IM syringe.
4. Take the pin off the IM syringe so you can see the small plastic hole (hold upright)
5. Take the slin pin and draw from the plastic hole on the IM syringe.
6. Push the IM plunger so that the solution touches the slin pin, and draw.
7. Store back in the fridge and replace IM pin.
The IM pin just keeps the syringe sealed when it's in the fridge. You won't pin it. It sounds confusing...maybe I'll make a video clip next time I crack open an amp.
You can use a sterile vial if you have one on hand, just keep in mind that every time a pin goes through the rubber stopper, it becomes dull/not as sharp. Another reason to use/draw from the IM syringe.
Hope I laid it out OK for ya.
/V
dont worry about the glass, amps are made to not break into tiny pieces. When i use sust amps i draw with a 25gauge pin, ive never had glass get in. BTW, using a pen cap to break the top of the amp works really well without cutting yourself.
weldingman
Registered
using a pen cap to break the top of the amp works really well without cutting yourself.
Very true Downtown, I do that a lot of the time.
Very true Downtown, I do that a lot of the time.
VictorZ06
Registered
I got so used to them I can crack em open with one hand. Besides, all the amps I use have scores on them and they are a sinch to snap off. Drawing oil with a 25g pin must take a long ass time. I draw with 18-20 then switch to a 22-23.
Pimprn, yes...you can draw using another IM pin. Doesn't matter, as long as it fits in the tiny plastic hole. I would use the thinnest gauge possible as it glides right in super easy, unlike oil.
/V
Pimprn, yes...you can draw using another IM pin. Doesn't matter, as long as it fits in the tiny plastic hole. I would use the thinnest gauge possible as it glides right in super easy, unlike oil.
/V
