Sus250 in syringe question? Help

[32bulkcycle]

About 4 weeks ago i got me and my buddy enough sus250 to do an 8 week cycle. Ive decided that i want to stretch the cycle out to 12 weeks as ive heard thats a better cycle length for sus250. At the same time my buddy has had bad side effects so he quit his cycle which works out perfect for me cause i can just use what he didNt use to stretch my cycle out to the 12 weeks. Heres where the question comes in. I dont know why, but for some reason, he pre-drew all of the gear out of the bottles so that its all already in the syringes. This may be a dumb question, but is that bad that he did that or will the stuff be fine sitting in the syringes untill I need it? Ive never heard of anyone doing that? I obviously just draw it out as i need it. What are peoples thoughts? Thanks. Id appreciate any imput.

 

[chucky1]

I heard it erodes the rubber plunger after a while so long term is not good but a couple hours should be fine. edit: you don't want to pin rubber particles

 

[Dath]

Some bros preload a weeks worth or even more. So it's common place. But as Chucky stated the rubber can deteriorate overtime. This is common place with EO (ethyl oleate)

 

[32bulkcycle]

Some bros preload a weeks worth or even more. So it's common place. But as Chucky stated the rubber can deteriorate overtime. This is common place with EO (ethyl oleate)

Well he put the gear in as soon as we got it 4 weeks ago so you think its probably not good?

 

[Dath]

Well he put the gear in as soon as we got it 4 weeks ago so you think its probably not good?

Not gonna say its no good....depending on your brand it may state on the vial the % of oil used ...be it cootonseed, ethyl oleate. Any of this info available bro?

 

[32bulkcycle]

Its cottonseed oil. Not sure of the percentage? I wish he hadnt put it all in the syringes. Then i wouldnt even have to worry about this

 

[VictorZ06]

If the syringe was stored needle point down and the rubber wasn't touching the gear, I'd say no worries.

But, as others have said...depending on the syringe, because there are dozens of different kinds of rubber used...there are teflon coated versions, bromo-butyl rubber, chloro-butyl rubber, isoprene/natural rubber, etc. All these are used for syringes and or stoppers on the vials/plungers.

If you plan to use it, filter and use a slin pin and inject via IM. I'd just toss it and get some more....but that's just me.




/V

 

[machinist9]

I have question,do you stand your vials up or leave them laying down?will it degrade the rubber in the vial if you don't stand them up?

 

[VictorZ06]

I have question,do you stand your vials up or leave them laying down?will it degrade the rubber in the vial if you don't stand them up?

I always keep them up....but it's the type of rubber being used that counts.




/V

 

[32bulkcycle]

I have question,do you stand your vials up or leave them laying down?will it degrade the rubber in the vial if you don't stand them up?

This is a good point because i keep my viles in my gym bag so they definitely get shifted around a lot. Im sure that rubber is fine thOugh.

 

[32bulkcycle]

Thanks

If the syringe was stored needle point down and the rubber wasn't touching the gear, I'd say no worries.

But, as others have said...depending on the syringe, because there are dozens of different kinds of rubber used...there are teflon coated versions, bromo-butyl rubber, chloro-butyl rubber, isoprene/natural rubber, etc. All these are used for syringes and or stoppers on the vials/plungers.

If you plan to use it, filter and use a slin pin and inject via IM. I'd just toss it and get some more....but that's just me.



/V

Thanks. I agree. I dont think im going to chance it. Too bad because it would Have saved me some money. My healths more important than money though.

 

[machinist9]

Thanks brothers for the help.

 

[aminoman74]

I wouldnt load mine to far as im sure the rubber will become weaker as there not maid for that kind of thing.